Suspension câble inox pour enseignes néon LED – Lot de 2 | Montage au plafond

This set is made for ceiling mounting, not for the wall. The sign hangs freely and is visible from both sides.

When in doubt, take the longer one: excess cable can be shortened with pliers, missing cable cannot be extended.

Two points so it hangs level. One set contains two complete suspensions. They go on the ceiling at the same spacing as the two mounting points on the top edge of your sign – so the panel hangs horizontally and does not turn.

• Free ceiling mounting – the sign floats in the room instead of sitting on a wall – twice the effect in a shop window
• Stainless steel – cable and fittings do not rust and do not yellow
• Four cable lengths to choose from – 0.5 m (1.6 ft), 1.0 m (3.3 ft), 1.5 m (4.9 ft) or 2.0 m (6.6 ft) – plus fine adjustment via the spring catch, excess trimmed with pliers
• Clamp instead of a drilled hole – the panel is clamped, so no extra hole goes into the acrylic
• For panels up to 10 mm (3/8") – our signs in 6 mm (1/4") acrylic glass fit with room to spare

• Shop windows – the sign hangs freely in the glass and glows inwards and outwards
• Counters and bar tops – an eye-catcher above the tap without costing any surface space
• Retail floors and reception areas – a sign or logo exactly where there is no wall
• High rooms and galleries – the adjustable length brings the sign down to eye level
• Room dividers and glass surfaces – where a wall mount is simply not possible

• 2× stainless steel ceiling plate with cable and spring catch
• 2× clamp with M5 hex screw for panels up to 10 mm (3/8")
• wall plugs and self-tapping screws for the ceiling mount

💡 Prefer the wall?
For wall mounting with and without drilling – suction cups, adhesive mounts, spacers and stands – have a look at our Mounting & Installation Collection.

• Quantity: 2 complete suspensions per set
• Material: stainless steel
• Cable: 1.5 mm (1/16") diameter, length per variant 0.5 m (1.6 ft) / 1.0 m (3.3 ft) / 1.5 m (4.9 ft) / 2.0 m (6.6 ft) – shortenable with pliers
• Ceiling plate: 40 mm (1 9/16") diameter, 33 mm (1 5/16") overall height, 1 mm (1/16") material thickness
• Screw holes: 3, each 5 mm (3/16")
• Clamp: 48.5 mm (1 15/16") high, 17 mm (11/16") wide, 3 mm (1/8") jaws, 10 mm (3/8") opening
• Clamping screw: M5 hex
• Length adjustment: stepless via spring catch, no tools needed
• Mounting location: ceiling – not intended for wall mounting

1. Measure the spacing – measure the two mounting points on the top edge of the sign and mark that spacing on the ceiling. Both points must sit on one line, otherwise the sign hangs crooked.
2. Fit the ceiling plates – drill at the marked spots, insert the plugs and screw the ceiling plates down with the self-tapping screws supplied. In concrete or plasterboard ceilings, use the plug type that suits the material.
3. Attach the clamps – slide the clamp over the top edge of the acrylic panel and tighten the M5 hex screw hand-tight. Do not overtighten – acrylic is sensitive to too much pressure.
4. Set the height – press the spring catch on the cable, slide the sign to the height you want and let go. Set both cables the same and the panel hangs level.

Tip: set the height with two people. One holds the sign, one works the catch – far quicker than doing it alone.

The cable suspension is plugged into the ceiling. How securely it holds depends on that ceiling – the set is only ever as strong as the anchor above it.

• Use the right plug for your ceiling. The plugs supplied are meant for solid materials. For plasterboard, cavity or timber ceilings you need the plug type made for them.
• Use both suspensions. With only one cable the sign turns and the whole load hangs from a single point.
• Tighten the hex screw hand-tight and check it again after the first few days. Overtightened, it can crack the acrylic panel.
• Do not mount above seating, beds, counters with guests or glass tables. Anything hanging freely belongs above a space where a fall would do no harm.
• Check the fit regularly. Slamming doors, draughts and vibration act on every ceiling mount.
• Check for cables and pipes. Always use a detector before drilling into a ceiling.

What is the stainless steel cable suspension for?
For ceiling mounting. The sign hangs from two stainless steel cables, freely in the room – in a shop window, above a counter or in a reception area. The set is not intended for wall mounting.

Will my acrylic panel fit the clamp?
The clamp takes panels up to 10 mm (3/8") thick. Our neon LED signs are made of 6 mm (1/4") acrylic glass and fit with room to spare.

How long is the cable?
You choose between 0.5 m (1.6 ft), 1.0 m (3.3 ft), 1.5 m (4.9 ft) and 2.0 m (6.6 ft). You fine-tune the height via the spring catch – press the catch, slide to height, let go. Any excess cable can be shortened with pliers.

Do I have to drill into the ceiling?
Yes. The ceiling plates are plugged and screwed; plugs and self-tapping screws are included. For plasterboard, cavity or timber ceilings, please use the matching plug type.

Do I need both suspensions?
Yes. With only one cable the sign turns and the entire load hangs from one point. Two cables keep the panel level and steady.

Do I have to drill a hole in the acrylic?
No. The clamp slides over the top edge of the panel and grips it with the M5 hex screw. No extra holes are needed.

Does the set rust?
Cable and fittings are stainless steel. They do not rust and do not yellow, even after years in a shop window.

How long does delivery take?
Accessories are in stock. Ordered together with a sign, everything ships together – the sign's delivery time of 6–14 days then applies.

Is there a warranty and a right of return?
Yes. 14-day returns plus a 2-year warranty. Contact: support@loveledlights.com.

Shipping
We work quickly to get your order shipped as soon as possible. As soon as it has been dispatched, you will receive an email with tracking information. Delivery takes 6–14 days. Thank you for your understanding and patience. 🙏

Returns
The item can be returned to us within 14 days of receiving your delivery. For the return process, please contact our support at support@loveledlights.com.

🌱 We rely on sustainable production to save resources and energy and to avoid unnecessary overstock. That is why every LED sign is individually made by hand only after your order comes in. Together for a clean and colourful world!